Search found 435 matches

by JoshKeller
26 Nov 2018, 17:12
Forum: Outboard Jets
Topic: 20/30 Johnson Jet leg.
Replies: 3
Views: 1936

20/30 Johnson Jet leg.

with a 180 lb boat, it should do just fine. the general suggestion is 25lbs per powerhead (not jet) horsepower
by JoshKeller
15 Aug 2018, 16:53
Forum: Outboard Jets
Topic: Decreased WOT speed and RPM's
Replies: 7
Views: 1571

Decreased WOT speed and RPM's

wish id have seen this post before answering on another site lol. unless you have higher than normal compression, running 93 octane is not letting you get full power from your motor. they are designed to run on 87, and the 93 is harder to ignite. combine this to the 36:1 ratio, you are seriously ric...
by JoshKeller
21 Jan 2018, 21:50
Forum: Outboard Jets
Topic: Johnson 90/65 Opinions?
Replies: 50
Views: 14855

Johnson 90/65 Opinions?

I run a 1760 xpress with a 115/80 omc. I started with a 90/65 and it turned 5200 rpm. Swapped powerheads, same impeller bumped up to 5450-5500 rpm and gained 2 mph. The proper liner and 80 hp impeller brought the rpm down to 5300. speed with the 90/65 was 29 mph. speed with the 115/80 and 65 impelle...
by JoshKeller
14 Mar 2017, 00:10
Forum: Member Karma
Topic: 13.5 ft stick steering cable
Replies: 0
Views: 1313

13.5 ft stick steering cable

Removed from my old boat and used on my new boat temporarily until i got everything where i wanted it and could measure out for a longer cable. Works fine, no binds.

Free, but not going to ship it. Its well greased and i dont want to deal with getting it in a box.
by JoshKeller
14 Mar 2017, 00:07
Forum: Sell it, buy it, swap it
Topic: Humminbird Matrix 97 $175
Replies: 6
Views: 2700

Humminbird Matrix 97 $175

Ill take my way point royalty check now lol
by JoshKeller
08 Mar 2017, 09:24
Forum: Electrical
Topic: Holy Grail of Trolling Motor Plugs
Replies: 42
Views: 7341

Holy Grail of Trolling Motor Plugs

Never had an issue running 36 volts to a marinco plug fighting heavy currents all day. Do you have an inline breaker? Possibly those 8 gauge cables not carrying enough juice for the length of the run, and getting hot enough at the plug joint to melt?
by JoshKeller
03 Mar 2017, 19:38
Forum: Outboard Jets
Topic: Hull dents
Replies: 47
Views: 6451

Hull dents

That looks like a stainless impeller to me.
by JoshKeller
02 Mar 2017, 22:55
Forum: Outboard Jets
Topic: OMC 3 Cyl. Jet
Replies: 4
Views: 1315

OMC 3 Cyl. Jet

It made a 4 mph difference on my old grizzly. Major improvement on hole shot too. And this was with a 49 cu inch short shaft 75, vs the torqueyer 56 cu in 70. Id be looking for a 70 over the 60. Same motor weight, and easier to find. https://i772.photobucket.com/albums/yy5/joshkeller8402/Mobile%20Up...
by JoshKeller
02 Mar 2017, 10:19
Forum: Sell it, buy it, swap it
Topic: johnson 75/50 jet
Replies: 1
Views: 1209

johnson 75/50 jet

sold
by JoshKeller
02 Mar 2017, 10:09
Forum: Outboard Jets
Topic: Hull dents
Replies: 47
Views: 6451

Hull dents

my ghetto way of checking clearance... pull out the spark plugs. shim the impeller. set the liner up. put 2 bolts in. have someone turn the flywheel by hand. shim it down as much as i can without rubbing.
by JoshKeller
02 Mar 2017, 10:02
Forum: Outboard Jets
Topic: I guess the impeller could use a cleaning up
Replies: 4
Views: 1164

I guess the impeller could use a cleaning up

redrum wrote:I'd order a stud kit for that pump and one of the newer style liners.

i HATE the studs that came with mine. took them out and replaced with stainless bolts. Everytime I hit something and then later needed to remove the boot, the studs were bent and made getting the boot off a chore.
by JoshKeller
26 Feb 2017, 22:14
Forum: Sell it, buy it, swap it
Topic: Humminbird Matrix 97 $175
Replies: 6
Views: 2700

Humminbird Matrix 97 $175

clear off those way points!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! [-X :lol:
by JoshKeller
25 Feb 2017, 22:51
Forum: Outboard Jets
Topic: Hull dents
Replies: 47
Views: 6451

Hull dents

I take mine as seriously as hitting it with the grinder, then removing the burr on the opposite side. Takes me longer to remove the boot than sharpen the impeller
by JoshKeller
25 Feb 2017, 22:48
Forum: Outboard Jets
Topic: I guess the impeller could use a cleaning up
Replies: 4
Views: 1164

I guess the impeller could use a cleaning up

I typically have to sharpen mine every 5 - 8 trips. I run through the nasties though. Last time i did mine, it was so bad the blades were hooked.
by JoshKeller
24 Feb 2017, 11:47
Forum: Outboard Jets
Topic: Hull dents
Replies: 47
Views: 6451

Hull dents

didnt you relocated batteries from when you first bought it? and i have a spare keeper washer. its double the thickness of the stock ones, so they wont break. only problem is, this tracker is .063 aluminum. Im not sure id want to touch it for fear of cracking/creasing/etc. and I dont see 5 mph from ...